This article will teach you how to make a bra strap bracelet. You will need to purchase the supplies and then follow the directions. These are easy to follow, so you’ll be able to create this bracelet in no time!
What is a Bra Strap Bracelet?
A Bra Strap Bracelet is a creative way to keep your bras in place and looking their best. You can make one with just a few supplies, including a bra strap and some elastic. Here’s how to do it:
- Cut the elastic into two equal lengths. The shorter length should be about 1 inch shorter than the bra strap.
- Thread one end of the elastic through the middle of the bra strap, making sure the ends are facing away from each other. Pull tight to secure.
- Thread the other end of the elastic through the loop on the other side of the bra strap, making sure the ends are facing each other again. Pull tight to secure.
- Trim off any excess elastic, if necessary.
Why Make a Bra Strap Bracelet?
Making a bra strap bracelet is a great way to use up those old bra straps! You can make the bracelet any size you want, and it’s a fun project to do with your friends. Here are some reasons why you might want to make a bra strap bracelet:
- It’s a creative way to use up old straps
- It’s a way to recycle something that would have gone to waste
- It’s a way to show your support for breast cancer awareness
- It’s a way to make yourself look stylish
Materials for Making A Bra Strap Bracelet
There are a few materials you will need for this project. A clasp, a piece of elastic, and a bra strap. The clasp can be found at most jewelry stores or you can make your own using a basic knotting technique. The elastic can be purchased at any store that sells clothing or accessories. The last item you will need is the bra strap. Make sure the strap is long enough to reach around your wrist comfortably.
The first step in making your bracelet is to cut the elastic into two equal pieces. One piece will be used for the back of the bracelet and the other will be used for the front. Next, take the back piece of elastic and wrap it around your wrist twice. Then, take the front piece of elastic and put it over top of the first one so that it covers it completely. Make sure that the ends of both pieces of elastic are touching each other so that they form a loop. Then, use a knotting technique to create a loop. You can either use a simple knot or use an overhand knot. Once you have created the knot, make sure that it is secure by pulling on both ends of the elastic simultaneously. Repeat this process with the other wrist until all straps are made
How to Make a Bra Band into Ribbon
If you want to make a bracelet out of your bra straps, this tutorial is for you! It’s simple and can be done in just a few minutes. Here’s how to make a bra strap bracelet:
1) Cut the band off of your bra straps. You should have about 2-3 inches of strap left over.
2) Take one end of the strap and fold it in half. Then, poke it through the hole on the other side of the ribbon.
3) Make a loop with the folded end of the strap and poke it through the hole again. Now, hold on to the ends of the ribbon and pull tight. The loop should now be sticking out from both sides of the ribbon.
4) Repeat Steps 2-3 until you have a bracelet that’s as long or short as you want it to be.
How to make the Bra Band
It’s been a while since we’ve done a tutorial on making something special, so here we go! This Bra Band Bracelet is super easy and perfect for adding a little pizzazz to any outfit. You’ll need:
-A bra strap
-Two small pieces of elastic (or thread)
-Sandpaper or a file
-Scissors
-Permanent marker or a glue gun
-Ruler or measuring tape
-Bra clasp
-Jump rings (if desired)
- Cut the elastic into two pieces about an inch wide. File or sand the edges smoothly.
- With the help of a ruler or tape measure, draw a line from one end of the elastic to the other. Make sure your line is even all the way across. Repeat on the other side of the elastic.
- Take one end of the elastic and place it over one of the marks you made on the bra strap. Hold it in place and make sure it’s evenly lined up across the strap. Use your fingers to pull tight on opposite sides of the elastic until it forms a loop. Trim any excess fabric (about 1/2 inch). Do
How to make the Ribbon
The ribbon is a great way to add a touch of class to your bracelet. You can make the bracelet in minutes by following these simple steps.
- Begin by cutting the ribbon into two equal pieces. Make sure the ribbon is long enough to tie around the wrist twice.
- Take one piece of ribbon and tie it around one end of the strand, making sure to tuck in the ends. Do the same thing with the other piece of ribbon.
- Tie each end of the ribbon together in a knot, making sure not to tighten it too much or you may damage the ribbon.
- Now take the two strands and tie them together in a loop, making sure to tuck in the ends again.
- Finally, make a small loop with one end of the strand and tuck it behind the other piece of ribbon. This will create your adjustable clasp.
Tutorial on how to make the Button Wraps
If you want to add a little something special to your bra straps, then a bracelet is the way to go. This tutorial will show you how to make a bra strap bracelet in just a few simple steps. The best part is that it’s very easy to make and can be done with just a few supplies.
You will need:
-Button clasp
-Bra strap
-Thread
-Scissors
-Needle nose pliers
-Ruler or tape measure
Step 1: Cut the bra strap in half. Be sure to measure the length of the strap before cutting so that you have enough material left over. You will need two pieces of strap for this project. Step 2: Take one of the halves of the bra strap and fold it in half, so that the raw edge is now facing outwards. Make sure that the folded edge is even with the edge of the button clasp. Use needle nose pliers to clamp down on the folded edge and start sewing it into place. Make sure not to sew too close to the clasp, or else your bracelet won’t stay closed! Step 3: Repeat steps 2
Instructions for making the Beads
This DIY Bra Strap Bracelet tutorial is quick and easy to follow, perfect for beginners. You will need: -bra straps -thread -beads (any size and color) -pliers -sewing needle -scissors -glue gun or hot glue ———————————————————————————————————— Step One: Cut the bra straps in half. Then measure the circumference of one strap around your wrist. This will be the bracelet’s base circumference.
Step Two: Take the other strap and measure its circumference around your wrist. This will be the bracelet’s top circumference.
Step Three: Use the sewing needle and thread to sew the two strap halves together, making sure that the base circumference matches up with the top circumference. You can also use a glue gun or hot glue to attach the straps together if preferred.
Step Four: Now it’s time to add the beads! Start by selecting some random beads and placing them on top of the seam where the two straps meet. Be sure to space them evenly so that they don’t look crowded once they’re glued on.
Step Five: To add more security, you can sew a piece of fabric over the seam where the bead tops meet
